Zoom
PRODUCT INFORMATION
*** AIO5 DOES NOT HAVE MOTOR PLUGS PRE SOLDERED ***
NEW release the new vtx firmware v1.7.0(Rev20240923). You can obtain and update your vtx from https://www.hd-zero.com/document
The update content is as follows:
• Add new target: HDZero AIO5.
• Support Lux camera.
• Fixed osd freezing at betaflight logo.
• Add new target: HDZero AIO5.
• Support Lux camera.
• Fixed osd freezing at betaflight logo.
HDZero AIO5
Description
HDZero AIO5 is the world’s first digital video AIO, enabling bind and fly 65mm whoops to weigh less than 19.4g. AIO5 integrates a F4 flight controller, HDZero 5.8GHz digital video transmitter, SPI 2.4GHz ExpressLRS 3.0 receiver, DSHOT protocol 4-in-1 ESC, and a 5V/1A BEC. The minimum voltage has been improved to be 2.3V, which ensures that video never stops transmitting before the motors stop working. Using a single thick PCB rather than a stack of 2 improves durability and simplicity – get ready for a new era of no-compromise tiny whooping in clear digital video!
The HDZero AIO5 is an excellent collaboration between Happymodel and HDZero.
Specifications:
- MCU: STM32F411 (100MHz, 512K Flash)
- Gyro: BMI270
- On board voltage and amperage meters
- Built-in 5A(each) BLHeli_S 4-in-1 ESC
- MCU: EFM8BB21
- HV Current: 5A continuous peak 6A (3 seconds)
- Factory firmware: O_H_5_48_V0.19.2.HEX
- Dshot600 ready
- Built-in 5.8G HDZero VTX
- RF output: 25mw/200mW
- Supported channels: R1-R8, F2/F4, L1-L8
- UFL connector (ultra-lite linear antenna included)
- Built-in SPI ExpressLRS 2.4GHz receiver
- Packet rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
- Pre-soldered enamel wire antenna
- Telemetry output power,12dBm
- Built-in 5V 1A BEC
- Flight controller firmware target: CRAZYBEEF4SX1280
- Power supply: 1S battery (2.5V – 4.35V)
- Fully compatible with the popular whoop frames
- Board size:28.5x28.5mm with a 25.5x25.5 mounting hole size
- Weight: 5.7g(without motor plugs), 6.3g (with motor plugs)
HDZero AIO5 User Manual_v0.1.pdf
Flight Controller Warranty Policy
At weBLEEDfpv, we are committed to providing high-quality products. However, due to the technical nature of flight controllers and the precision required for installation, our warranty policy for flight controllers is as follows:
1. No Warranty Post-Soldering:
Once any soldering has been performed on the flight controller, we are no longer responsible for replacements, repairs, or refunds. The process of soldering can introduce various factors that may lead to damage, and we are unable to control or verify the conditions in which the soldering was conducted.
2. Pre-Soldering Inspection:
Before you begin soldering, we recommend carefully inspecting the flight controller for any potential issues. If any defects or issues are found prior to soldering, please contact us immediately for a replacement.
3. User Responsibility:
Soldering requires skill and experience, and improper techniques may result in damage to the flight controller, including but not limited to overheating or lifting solder pads. Please ensure you are confident in your soldering abilities before proceeding, as we cannot be held liable for any damages caused during installation.
4. Final Sale:
All flight controller sales are final once the product has been modified or soldered. We are unable to offer returns or exchanges on used or modified products.
RELATED PRODUCTS
