FPVCycle

FPVCycle 23mm Short Motor - THE Cinewhoop motor

$20.99 USD $19.99 USD Save 5%
KV
12 in stock, ready to ship
Notes

The update:
New look, minor tweak to internal stator design, improved low end prop handling, new prop mount, less weight, screw retained bell.  These motors are compatible with the previous 2203/4.  If you mix them on the same craft with similar kv, you won't be able to tell a difference in flight performance.

We haven't used a better performing 3" cinewhoop motor than this one...

 



This motor is specifically designed for the following uses:
3” ducted whoop
4” anything
5” light blade and low general AUW for 5”

Matching products:
CineSplore w/ Gemfan 75mm CineWhoop prop
PowerPick 4” with Gemfan 4023 prop
PowerPick 5” with Gemfan 5125 prop
Fouride 4” with Gemfan 4023 prop
Fouride 5” with Gemfan 5125 prop
Red T-mount props are fantastic with Gemfan 4024
3000kv version is suitable for CineWhoop/CineSplore on 6S if desired

Recommended battery options:
3S 1000-1500mah on 3450kv with CineWhoop 3”or 4” open prop
4S 1100-1300mah on 3450kv with CineWhoop 3” or 4” open prop
3S 1100-1300mah on 3450kv with 4" or 5" open prop
4S 900-1300mah on 3450kv with 4" open prop
4S 1100-1300mah on 2350kv with 5" open prop
4S 1100-1300mah on 3450kv with CineWhoop 3”
5S 1100-1300mah on 2350kv with CineWhoop 3” or 4” open prop
6S 850-1000mah on 2350kv with CineWhoop 3”

You’re welcome to run full 4S with no throttle cut on 3450kv and 5” but be warned that it will be extremely overpowered on a very light platform and a challenge to deal with the electronic noise due to the high power.  If your filters and overall electronic management is not done right, the motors have some risk of burning.  Even though these motors have super high temperature enamel coating on the winds, we are not responsible for burnt motors due to misuse.

Specifications:

  • 23mm stator diameter, greater than 3mm stator height
  • 12x12mm M2 mounting pattern (not flush mount)
  • ~17g with ~80mm length wires
  • ~20g with prop adapter, nut and 240mm 24awg wire length
  • 0.15mm Kawasaki High performance laminations
  • N52SH ARC magnets
  • 3mm grade 5 titanium internal shaft
  • M3 grade 5 titanium prop shaft with M5 adapter
  • 3x8x4mm 683zz Japan ISC Custom bearings
  • 7075-T6 aluminum casing
  • 260℃ enamel coated single wrap oxygen-free copper windings
    Product information

    All parts are shipped fast from SYRACUSE, NEW YORK & some DROP SHIP ORDERS from San Diego, California. If there's an issue with something, please let us know and we will do our best make it right! SaltCtyRacingFPV, LLC dba "weBLEEDfpv.com" offers a (30) day return policy on all new unopened equipment, starting from the date the product(s) was delivered to the customer. Anything beyond (30) days of delivery will not be eligible for return. If the product(s) received have been opened, used or damaged, no return options will be offered. If the item is in brand new condition but requires to be repackaged, a (15%) restocking fee will be applied. The shipping cost for any unwanted product will not be refunded by SaltCtyRacingFPV "weBLEEDfpv.com" (It is recommended to choose a return shipping method with tracking).

    **************************************************************************

    Please email at SaltCtyRacingFPV@gmail.com to contact us and initiate a return. Please contact us first before sending anything back. 

    **************************************************************************

    Flight Controller / VTX Warranty Policy
     
    At weBLEEDfpv, we are committed to providing high-quality products. However, due to the technical nature of flight controllers and VTX's the precision required for installation, our warranty policy for flight controllers is as follows:
     
    1. No Warranty Post-Soldering: 
       Once any soldering has been performed on the flight controller / VTX's, we are no longer responsible for replacements, repairs, or refunds. The process of soldering can introduce various factors that may lead to damage, and we are unable to control or verify the conditions in which the soldering was conducted.
       
    2. Pre-Soldering Inspection: 
       Before you begin soldering, we recommend carefully inspecting the flight controller  / VTX's for any potential issues. If any defects or issues are found prior to soldering, please contact us immediately for a replacement.
     
    3. User Responsibility: 
       Soldering requires skill and experience, and improper techniques may result in damage to the flight controller, including but not limited to overheating or lifting solder pads. Please ensure you are confident in your soldering abilities before proceeding, as we cannot be held liable for any damages caused during installation.
     
    4. Final Sale: 
       All flight controller sales are final once the product has been modified or soldered. We are unable to offer returns or exchanges on used or modified products.
    **************************************************************************

    ⚠️ FPV DIGITAL SYSTEM NOTICE

    HDZero, Walksnail, VTX systems, and ultra-micro FPV electronics generate heat quickly while powered and require proper handling during setup and troubleshooting.

    Bench setup without airflow/cooling can result in excessive heat buildup.

    Once powered, configured, firmware updated, soldered, flown, or modified, products are considered used.

    Manufacturer warranty may apply for BNF drones and electronic systems.

    **************************************************************************

    Lithium Ion Battery No Acceptance Policy

    For our lithium ion battery products, all sales are final. This means:

    • No Returns or Exchanges: Once your purchase is completed, we do not accept returns, exchanges, or cancellations.
    • Customer Responsibility: Please review all product specifications and details carefully before making your purchase.
    • Safety and Compliance: Due to safety standards and regulatory guidelines, we cannot process any post-sale modifications.

    **************************************************************************

    Thank you for your understanding.

    Drop Us A Line

    We’re happy to answer any questions you have or provide you with an estimate. Just send us a message in the form below with any questions you may have.