NewBeeDrone
NewBeeDrone Cockroach 75mm Brushless Frame
$7.99 USD
/
13 in stock, ready to ship
Design Intent Behind the Frame:
For this frame we worked to develop a platform that would neither fall below expectations nor limit the creativity of the FPV community. Lightweight and versatile. We improved durability and worked to deliver a vibrational signature that made tuning easier so you can get the most performance out of the NewBeeDrone flight controllers and motors. Every gram of frame material was either added or taken away to ensure that what was left, was there for a reason.
Lightweight and Durable:
We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls with a total weight 6.98g.
Traditional Looks and Geometry:
This 75mm Cockroach frame has adaptable FC locations and a multitude of additional mounting points across the frame. We delivered a frame that has 2 board locations with 1x1inch or 25.4x25.4mm hole spacing. One mounting location on top and another below to mount an additional board like a DVR or a 4K HD recording board. The 2-board mounting adaptability allows for the possibility for a pusher-style flying configuration to be used as well.
1mm Carbon Fiber Plate
A 1mm carbon plate is included for increased durability insurance. Though the frame can be flown without it, the carbon allows for additional adaptability and opens the frames use for exciting opportunities in a pusher-style configuration. Flip the frame over and install. Please be aware, the motor screws that come with the 75mm frame are expected to be used with the carbon fiber. If you choose to use them without the carbon fiber plate – the screws may contact the motor PCB. Please be aware.
Flexible Battery Solutions
This 75mm frame does not come with just one limiting battery mounting solution. We understand that depending on the utility and flying style, many people want to run one or two 300mah Nitro Nector Golds in the traditional battery position or in a ‘toilet-tank’ position. We have developed several printable, TPU, battery mount solutions to use with the frame and are always open to your suggestions.
Easy and Inexpensive. None of this is any good if its super difficult to use and/or super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine tuned to make installation and removal much easier.
Any of our other whoop BNF's can be directly dropped-in into the 75mm frame. However, in some cases, the motor wires are just a touch too short. We recommend picking up some longer motor wires just in case.
JST Whoop Motor Wire Replacement Set
Recommended Setups:
Controlled Indoor:
NBD BeeBrain Brushless v2
BeeEye Camera with Goober Canopy
1x 1s Battery – 300mah Nitro Nector Gold
NBD Gold Motors 18000kv
NBD 40mm Azi Props
*Optional:
1mm Carbon Fiber Plate
1s TPU Battery Mount Setup
1s Battery Sling (if not using the Carbon Fiber Plate)
Insta360 Go Mount
Outdoor or long range:
NBD BeeBrain Brushless v1
BeeEye Camera with Goober Canopy
Crossfire nano receiver
NBD Silver Motors 16420kv
NBD 40mm Azi Props
2S Series adaptor cable
*Optional:
1mm Carbon Fiber Plate
2x 1s TPU Battery Mount Setup
2x1s Battery Sling (if not using the Carbon Fiber Plate)
Battery mount for 1s Nitro Nectar included
3D Print parts:
1S 1NitroNectar Gold Battery mount
2S 2NitroNectar Gold Battery Mount For HD Whoop
1S 1xNitroNectar GoldBattery Mount without Carbon fiber plate
2S 2x NitroNectar Gold Battery mount without carbon fiber plate
1S Large size battery 450mah
For this frame we worked to develop a platform that would neither fall below expectations nor limit the creativity of the FPV community. Lightweight and versatile. We improved durability and worked to deliver a vibrational signature that made tuning easier so you can get the most performance out of the NewBeeDrone flight controllers and motors. Every gram of frame material was either added or taken away to ensure that what was left, was there for a reason.
Lightweight and Durable:
We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls with a total weight 6.98g.
Traditional Looks and Geometry:
This 75mm Cockroach frame has adaptable FC locations and a multitude of additional mounting points across the frame. We delivered a frame that has 2 board locations with 1x1inch or 25.4x25.4mm hole spacing. One mounting location on top and another below to mount an additional board like a DVR or a 4K HD recording board. The 2-board mounting adaptability allows for the possibility for a pusher-style flying configuration to be used as well.
1mm Carbon Fiber Plate
A 1mm carbon plate is included for increased durability insurance. Though the frame can be flown without it, the carbon allows for additional adaptability and opens the frames use for exciting opportunities in a pusher-style configuration. Flip the frame over and install. Please be aware, the motor screws that come with the 75mm frame are expected to be used with the carbon fiber. If you choose to use them without the carbon fiber plate – the screws may contact the motor PCB. Please be aware.
Flexible Battery Solutions
This 75mm frame does not come with just one limiting battery mounting solution. We understand that depending on the utility and flying style, many people want to run one or two 300mah Nitro Nector Golds in the traditional battery position or in a ‘toilet-tank’ position. We have developed several printable, TPU, battery mount solutions to use with the frame and are always open to your suggestions.
Easy and Inexpensive. None of this is any good if its super difficult to use and/or super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine tuned to make installation and removal much easier.
Any of our other whoop BNF's can be directly dropped-in into the 75mm frame. However, in some cases, the motor wires are just a touch too short. We recommend picking up some longer motor wires just in case.
JST Whoop Motor Wire Replacement Set
Recommended Setups:
Controlled Indoor:
NBD BeeBrain Brushless v2
BeeEye Camera with Goober Canopy
1x 1s Battery – 300mah Nitro Nector Gold
NBD Gold Motors 18000kv
NBD 40mm Azi Props
*Optional:
1mm Carbon Fiber Plate
1s TPU Battery Mount Setup
1s Battery Sling (if not using the Carbon Fiber Plate)
Insta360 Go Mount
Outdoor or long range:
NBD BeeBrain Brushless v1
BeeEye Camera with Goober Canopy
Crossfire nano receiver
NBD Silver Motors 16420kv
NBD 40mm Azi Props
2S Series adaptor cable
*Optional:
1mm Carbon Fiber Plate
2x 1s TPU Battery Mount Setup
2x1s Battery Sling (if not using the Carbon Fiber Plate)
Battery mount for 1s Nitro Nectar included
3D Print parts:
1S 1NitroNectar Gold Battery mount
2S 2NitroNectar Gold Battery Mount For HD Whoop
1S 1xNitroNectar GoldBattery Mount without Carbon fiber plate
2S 2x NitroNectar Gold Battery mount without carbon fiber plate
1S Large size battery 450mah
Product information
All parts are shipped fast from SYRACUSE, NEW YORK & some DROP SHIP ORDERS from San Diego, California. If there's an issue with something, please let us know and we will do our best make it right! SaltCtyRacingFPV, LLC dba "weBLEEDfpv.com" offers a (30) day return policy on all new unopened equipment, starting from the date the product(s) was delivered to the customer. Anything beyond (30) days of delivery will not be eligible for return. If the product(s) received have been opened, used or damaged, no return options will be offered. If the item is in brand new condition but requires to be repackaged, a (15%) restocking fee will be applied. The shipping cost for any unwanted product will not be refunded by SaltCtyRacingFPV "weBLEEDfpv.com" (It is recommended to choose a return shipping method with tracking).
Please email at SaltCtyRacingFPV@gmail.com to contact us and initiate a return. Please contact us first before sending anything back.
Flight Controller / VTX Warranty Policy
At weBLEEDfpv, we are committed to providing high-quality products. However, due to the technical nature of flight controllers and VTX's the precision required for installation, our warranty policy for flight controllers is as follows:
1. No Warranty Post-Soldering:
Once any soldering has been performed on the flight controller / VTX's, we are no longer responsible for replacements, repairs, or refunds. The process of soldering can introduce various factors that may lead to damage, and we are unable to control or verify the conditions in which the soldering was conducted.
2. Pre-Soldering Inspection:
Before you begin soldering, we recommend carefully inspecting the flight controller / VTX's for any potential issues. If any defects or issues are found prior to soldering, please contact us immediately for a replacement.
3. User Responsibility:
Soldering requires skill and experience, and improper techniques may result in damage to the flight controller, including but not limited to overheating or lifting solder pads. Please ensure you are confident in your soldering abilities before proceeding, as we cannot be held liable for any damages caused during installation.
4. Final Sale:
All flight controller sales are final once the product has been modified or soldered. We are unable to offer returns or exchanges on used or modified products.
**************************************************************************
Lithium Ion Battery No Acceptance Policy
For our lithium ion battery products, all sales are final. This means:
- No Returns or Exchanges: Once your purchase is completed, we do not accept returns, exchanges, or cancellations.
- Customer Responsibility: Please review all product specifications and details carefully before making your purchase.
- Safety and Compliance: Due to safety standards and regulatory guidelines, we cannot process any post-sale modifications.
Thank you for your understanding.
Drop Us A Line
We’re happy to answer any questions you have or provide you with an estimate. Just send us a message in the form below with any questions you may have.
